Skip to content
Machines& Material Handling
Buy on Chat Login
PackForge Buy on Chat 0
Fault finder · cap, rim, time, head

Induction Sealer Not Sealing: Find the Cause

When foils lift, stick on one side or burn, the machine is rarely the culprit. This page walks through the checks in the order a service engineer would make them, so you can fix most problems at the bench in minutes.

Buy Induction Sealing Machines online

Price + 18% GST · free delivery across India · Buy Now or Add to Cart

View all →
Quick answer: An induction sealer that is not sealing usually has a cap problem, not a machine problem. Check in this order: the cap has an aluminium induction liner, the cap is tight and even, the rim is clean and dry, the sealing time is long enough, and the head is flat and centred. If the display stays dark or the head stays cold on a known good cap, call service.

Why is my induction sealer not sealing?

A foil bonds only when three things happen together: the aluminium layer heats, the heat-seal coat melts, and the cap holds that coat pressed against a clean rim while it cools. Break any one of these and the foil peels off. Most failed seals come from the cap, the liner or the rim, and most of the rest from the setting. A faulty machine comes last.

So before you open anything or book a visit, run the checks below on three or four bottles. Change one thing at a time, so you know which change fixed it.

Check these six things, in this order

  1. Is there foil in the cap? Unscrew a cap and look. You need a liner with an aluminium layer. A plain plastic cap or a cardboard-only wad will not seal at any setting.
  2. Is the liner the right way up and the right type? The heat-seal coat must face the bottle and must suit the bottle material. A liner meant for glass may not bond to HDPE.
  3. Is the cap tight and even? Screw caps with the same force each time. A loose or cross-threaded cap leaves gaps in the ring.
  4. Is the rim dry? Oil, syrup, cream or powder on the rim stops the coat from bonding. Wipe rims after filling.
  5. Is the time right? Too short leaves a weak bond; too long scorches the foil and can soften the cap. Adjust in small steps and peel after each change.
  6. Is the head flat and centred? On hand-held models, a tilted head seals one side. On the conveyor IS200, set the guides so each cap passes straight under the coil.
PackForge Heavy Duty Induction Sealing Machine 20-100 mm
PackForge Heavy Duty Induction Sealing Machine 20-100 mm

Induction sealer faults, causes and fixes

FaultLikely causeFix
Foil not bonded anywhereNo aluminium liner, or time much too shortConfirm liner; raise the time step by step
Foil bonded on one side onlyCap loose or tilted, head off centreTighten evenly; hold the head square over the cap
Foil peels too easilyTime slightly short or wrong liner coatLengthen time a little; ask the cap supplier about the coat
Foil brown, burnt smellTime too long for that capShorten the time
Cap top soft or out of shapeOver-heating, often on small capsShorten the time; small caps heat fastest
Good seals, then failures later in the batchRims getting wet as filling goes onClean the filling nozzle; wipe rims
Large jars seal badly, small bottles fineCap bigger than the model's rangeCheck the model: 20–80, 20–100 or 20–130 mm
Foil sticks to the cap, not the bottleLiner fitted upside down or wrong liner typeReplace with the correct induction liner
Display dark, no responseSocket, plug or cableTry another socket; check the plug; then call service
Display on but head stays coldMachine faultStop and call service with a short video

Is the cap within the machine's range?

Each PackForge hand-held sealer covers caps from 20 mm up to its top size. If your biggest cap is larger than that, the head cannot heat the whole ring and the edge stays loose.

Measure across the top of the cap, the outer diameter, not the bottle neck.

When the sealer itself is at fault

If a cap that sealed well yesterday will not seal today, with the same liner and the same time, look at the machine:

  • Check that the head cable is not cut, crushed or pulled at the plug.
  • Make sure the vents on the control box are not blocked by cartons or cloth.
  • On Heavy Duty models, overload protection can stop the machine; switch off, let it rest and restart.
  • On the IS200, the coil is water-cooled; check the cooling as shown in its manual before a long run.

Do not open the control box yourself. Call +91 95822 69346 or +91 98184 33150 and send a short video of the display and one test seal on WhatsApp. Within the warranty period manufacturing defects are covered: 12 months on Standard models and 5 years on Heavy Duty models, as stated on each product page. Read the PackForge warranty terms for what is included.

DGYF-600C Induction Sealing Machine 20-130 mm
DGYF-600C Induction Sealing Machine 20-130 mm

Prevent the problem coming back

  • Keep a written setting per cap size and liner next to the machine.
  • Peel-test the first bottles of every batch and after any change of cap lot.
  • Tighten caps the same way every time, ideally with a capper.
  • Wipe the head with a dry cloth at the end of each shift.
  • Train every new operator on how to use an induction sealer before they run a batch.

For wear parts and upkeep plans, see spares and AMC. The full range and prices are on the induction sealer page.

Still not sealing?

Send us a short video of one seal, a photo of the cap liner, the cap size and your model. We will tell you what to change.

Questions buyers ask

Why does the foil stick to the cap instead of the bottle?

The liner is usually the wrong type or fitted upside down, so the heat-seal coat is facing the cap. Ask your cap supplier for an induction liner with the coat facing the bottle, made for your bottle material.

Why does my induction seal leak after a few days?

The bond was weak from the start, usually from a loose cap, a damp rim or too short a time. Peel-test a few bottles from each batch; a good foil comes away in one piece covering the full rim.

Can a higher time fix every weak seal?

No. If the cap is loose or the rim is oily, more time only scorches the foil. Fix the cap and the rim first, then adjust the time in small steps.

Induction sealer seal kyun nahi kar raha?

Pehle dekhein cap mein aluminium foil liner hai ya nahi, cap tight hai ya nahi aur bottle ka muh sukha hai ya nahi. Phir time thoda badha kar test karein. Display band ho to service ko call karein.

Is a failed seal covered by warranty?

A seal that fails because of the cap, liner or setting is not a machine defect. If the machine itself stops heating, manufacturing defects are covered for 12 months on Standard models and 5 years on Heavy Duty models.

Which caps cannot be induction sealed?

Caps with no aluminium liner, caps bigger than the model's range, and metal lids. Send a photo of your cap on WhatsApp and we will tell you before you change anything.

Send your requirement

Tell us the job rather than the model number — what you pack, how many a day and the city.

Call +91 95822 69346+91 98184 33150

Please put in a name and a mobile number we can reach.

Delivery is free anywhere in India, and GST is shown separately on every rate.

Written by the PackForge Technical Team, Faridabad. Updated 22 November 2026.

New Here? Grab Up to 10% Off Your First Order.

Subscribe with your email for first-order offers, deals and new arrivals.

Related machines and guides

Main machines

Carton Sealing Machine|Impulse Sealer|Heat Sealing Machine|Hand Sealing Machine|Strapping Machines and Tools|Stretch Wrapping Machines|Continuous Band Sealing Machine|Cup Sealing Machine|Induction Sealing Machine|Handheld Inkjet Printer

By product range

Fully Automatic Strapping Machines|Semi Automatic Strapping Machines|Low Table Top Strapping Machines|Pneumatic Strapping Tools|PP Strap Rolls|Strapping Machine Spares|Semi Automatic Carton Sealing Machines|Compact Carton Sealing Machines|Automatic Random Carton Sealing Machines|BOPP Tape Rolls|Carton Sealer Spares|Box Wrapping Machines with Top Press|Turntable Stretch Wrappers|Stretch Film Rolls|Wrapping Machine Spares|Hydraulic Hand Pallet Trucks|Drum Carriers & Lifters|Pallet Truck Spares & Wheels|Material Handling Trolleys|Machine Spare Parts

Machines and consumables

Fully Automatic Strapping Machine, PP Strap, Touch HMI|Semi Automatic Strapping Machine, Arch Type, PP Strap|Low Table Top Semi-Automatic Strapping Machine, Compact|Pneumatic strapping tool, PP and PET strap|Machine-grade PP strap|Semi Automatic Carton Sealing Machine, Top & Bottom Tape|Compact Carton Sealing Machine for Small Cartons|Automatic Random Carton Sealing Machine, Auto Size Adjust|Box Wrapping Machine with Top Press, Turntable Stretch Wrapper|Turntable stretch wrapper|Hydraulic Hand Pallet Truck, 2.5 Ton Capacity, Nylon / PU Wheels|Material Handling Drum Carrier & Lifter, 350 kg Capacity|Platform trolleys

Hand sealing machines

Hand Sealer|Poly Bag Sealing Machine|Pouch Sealing Machine|Packet Sealing Machine|Plastic Bag Sealing Machine|Bag Sealing Machine|8 Inch Hand Sealing Machine|12 Inch Hand Sealing Machine|16 Inch Hand Sealing Machine|Foot Sealing Machine|Table Top Sealing Machine|How to Choose a Hand Sealing Machine|Hand Sealer or Band Sealer?

Bengaluru

Packaging Machines in Bengaluru|Carton Sealing Machine in Bengaluru|Hand Sealing Machine in Bengaluru|Cities We Supply

PackForge AssistantFaridabad works · packaging, material handling, agriculture
ContactWhatsAppCall